How to clean an iron from a stick

Modern irons are rarely covered with soot, but no one is safe from accidents. Each housewife, perhaps, has a couple of ideas on how to clean the iron from the burn, and we offer you specific means and actions for cleaning the sole of the iron. This can be done easily, quickly and efficiently, restoring the performance of your iron.

to contents ↑

How to clean the burn on the iron?

In order for the work surface of your assistant to shine again and to smoothly iron, you may need the following tools:

• baking soda;
• vinegar;
• salt;
• hydrogen peroxide;
• acetone;
• lemon acid;
• plastic brush;
• paraffin candle;
• special tools;
• lips, rags and napkins;
• hydroperit tablet;
• water.

Important! You should immediately pay attention to two rules:

• Be sure to unplug the appliance before cleaning if it is not intended to be turned on during the procedure.
• Never clean the work surface with hard abrasive washcloths, otherwise it will be completely damaged and it will not be possible to restore smoothness.

to contents ↑

How to clean the iron from the stick?

Choose the tool that is at your fingertips at home, read the proposed instructions for its use and act clearly according to the scheme to quickly deal with the problem, but be careful.

Method 1

To clean the soleplate with soda, follow these steps:

1. Dilute soda in water with a calculation of 1: 1.
2. Preheat and unplug the iron.
3. Dampen the sponge in the solution.
4. Wipe the entire surface.
5. Remove any residue with a clean, damp cloth.

Note: for spot deposits, you can pour soda directly on the stain and gently rub it, and then remove the remnants of the product.

Method 2

Deposits can be removed quickly with acetone and vinegar. You need to do this like this:

1. Take a cotton swab.
2. Moisten with a product.
3. Treat the surface.
4. Wipe with a damp cloth.
5. Dry the sole of the appliance.

Method 3

For particularly stubborn stains, soda and vinegar can be combined. It is safe to do it like this:

1. Quench soda with vinegar.
2. Arm yourself with woolen cloth.
3. Wet the cloth with a solution.
4. Remove carbon deposits.
5. Dry the cleaned surface.

Note: this method should be used in a well-ventilated area.

Method 4

Hydrogen peroxide also removes dark spots and adhering villi well. This is done correctly like this:

1. Take a rough cloth.
2. Moisten with a product.
3. Wipe the entire surface.
4. Let it dry.

Method 5

Calcium deposits in the holes and black deposits on the working surface of the iron, which has a steam mode, are removed using the self-cleaning function. If there is no such function, then there is another similar “grandfather” way:

1. Take a large pan.
2. Pour water into it.
3. Add a special cleanser or citric acid.
4. Put the iron stand on the bottom of the pan.
5. Install the appliance on it.
6. Heat the pan over low heat for 30 minutes.
7. Remove the iron from the structure.
8. Wipe with a dry cloth.

Note: make sure that water does not rise above the sole of the appliance. It is possible to process with steam even less time, it depends on the level of pollution.

Method 6

It is very effective and easy to clean the iron with salt, if you use it this way:

1. Place a thick cloth on the ironing board.
2. Pour fine salt on it.
3. Iron it with a well-heated iron.
4. Cool the unit.
5. Wipe with a dry cloth.

to contents ↑

How else can you quickly remove the cinder from the iron?

If you are looking for the fastest solution, then it is unlikely that you will be able to do without suitable chemistry or mechanical cleaning.

Option 1

A tablet of hydroperite is very suitable for removing a large area of ​​a stick. You need to work with it like this:

1. Take the whole pill.
2. Heat the iron well.
3. Wipe the entire contaminated surface with a tablet.
4. Rinse off exfoliated soot under running water.

Note: Ventilate the area well after cleaning.

Option 2

Use a plastic brush:

1. Take the tool.
2. Preheat the iron.
3. Rub the sole.
4. Wipe with a damp cloth.

Option 3

Very effective in this matter are special cleansing pencils. You need to use them like this:

1. Preheat the appliance.
2. Pour the contents of the pencil onto the sole of the instrument.
3. Leave on for 10 minutes.
4. Wipe with a damp soft cloth.
5. Wipe with a dry cloth.

Note: read the composition of the tool. Make sure that there are no toxic elements in it.

Option 4

A paraffin candle copes well with soot on the working part of such a device. Follow this step-by-step instruction for the effectiveness of the product:

1. Wrap the candle in cotton.
2. Heat the iron.
3. Wipe the burning spots with a candle in a cloth.
4. After burning, cool the appliance.
5. Get rid of traces of paraffin along with dirt.

Note: this method is great for ceramic-coated appliances on the sole.

to contents ↑

Useful Tips

• The most effective way to clean a heated iron, but disconnected.
• After any cleaning, iron the unnecessary, preferably white, fabric to make sure that the entire coating has really come off.

to contents ↑

Stock footage

Even if you had to face the problem of a burnt iron, this is not a reason to be upset. With the help of our tips, you can quickly clean it in 5-10 minutes!