Polyurethane foam cleaner

One of the commonly used materials in construction is polyurethane foam. How effective it is in use, such a difficult form of cleaning contaminated surfaces during its operation. Therefore, in this situation, it is advisable to take care of the foam cleaner. It is necessary to find an effective tool that can solve this problem. We will consider each polyurethane foam cleaner in this article.

to contents ↑

Polyurethane foam cleaner - how to wash the polymer?

When working with polyurethane foam, you need to be extremely careful:

• Before starting work, it is necessary to protect all floor and wall surfaces with film, paper, cardboard.
• It is advisable to remove the resulting dirt immediately, because after a while it will be quite difficult to solve this “snag”.

In such cases, the sealant hardens instantly and at the moment chemical solvents come to the rescue, which must be taken care of in advance:

• It is advisable to thoroughly study the use of the selected cleaner, and you also need to definitely test.
• To do this, pour a small amount of the reagent to the place of contamination and monitor the reaction.

Important! Thus, you can verify the correctness of the selected means, since improper use leads to the corruption of the item. Unpleasant stains, dull colors - this is not an exhaustive list of the results of an inappropriate foam cleaner.

When cleaning the surface of the polymer from the resulting pollution, you must be extremely careful, since there are solvents that can destroy the top layer of plastic. In this case, it is preferable to impregnate a small piece of cloth with a cleaner and slightly moisten the place of contamination. As a result of the reaction, the sealant from the dirty area will gradually dissolve.

to contents ↑

How to wash foam quickly and easily?

Carrying out repair work, it is worth remembering several simple rules:

1. It is necessary to put on work clothes, especially not to forget gloves made of thick fabric or rubber.
2. Cover the area of ​​work, which is subject to possible contamination, with old newspapers, cardboard or paste over with paper tape. If, however, the sealant left its marks on his hands, clothes, or on the floor, urgent measures must be taken.
3. Chemicals cannot be used to wash hands - they can lead to severe burns.
4. In case of fresh contamination, it is undesirable to spread fresh mass over the entire surface. It is necessary to carefully cut off the top layer with a knife or putty knife, and then use a foam cleaner.
5. Freshly emerged sealant cannot be washed with water, since it is part of the chemical polymerization reaction of this sealant.

Important! Cleansing from sealant as a result of repair work is the most problematic. The presence of a pre-prepared cleaner from the mounting foam greatly simplifies the efforts associated with its cleaning.

How to act:

1. They try to immediately clean the contaminated area of ​​the material using iron and rubber blades.
2. Starting to clean from extreme moments to the central point, it is advisable to try not to increase the contaminated fragment.
3. Further, the final cleaning of the newly appeared sealant is immediately carried out.
4. If time is lost and the polymerization process is completed, use a cutter. The upper dried area is cut off, and then the remaining contamination is removed with a foam cleaner.

Important! Very often, sealant manufacturers recommend the appropriate cleaning agent in the kit. Each producer in the development of the appropriate product uses its own chemical formulas. And not every cleaning foam cleaner will cope with the pollution of various accessories in a high-quality way:

• Most of the cleaning substances effectively affect the newly emerged pollution.
• The sealant crystallizes very quickly - in this case it is already advisable to use immeasurably strong solvents.

to contents ↑

Foam cleaner - until dry

Still not hardened sealant it is quite easy to remove with a plastic or rubber scraper. The process must be carried out carefully, without smearing the contaminated surface. After that, it is worth using a dense fabric and special cleaning foam cleaners, which are widely used when installing doorways and windows.

Important! If sealant gets on the parquet or linoleum it is not necessary to rush at all. Within two hours, a polymerization reaction occurs, as a result of which the foam mass becomes stretching rubber. After that, it is possible to separate the sealant from the parquet or linoleum without any problems, without harming the floor itself.

Most often, the main purpose of the cleaner is to rid the mounting gun of the remaining foam. That is why manufacturers produce specially designed cylinders with solvents.

Important! It is more convenient to clean the mounting gun in an open space or in a well-ventilated area. Be sure to follow the mounting gun so as not to stain everything around.

In order to clean the mounting gun, you need to:

1. Remove the prepolymer balloon.
2. Squeeze the trigger, release the gun from the remains of the sealant.
3. Attach solvent bottle.
4. Pull the trigger and release the spray from the gun.
5. Repeat this action until the gun releases clear fluid.

Important! In some cases, acetone can handle the removal of a contaminated surface. It must be remembered that it is not suitable for all plastic materials. A strong solvent can discolor hardware and, therefore, cause permanent damage to the surface.

to contents ↑

Hardened polyurethane foam cleaner - is there a way out?

Most often, contaminated areas are noticed only after the sealant hardens, which greatly complicates the cleaning process.

Important! The most effective and inexpensive tool for cleaning hardened sealant is dimethylformamide. It helps to get rid of mounting foam in just 45 minutes.

The action of all cleaning foam cleaners comes down to softening the sealant, which helps to remove dirt from the problem area more easily.

Important! Do not forget that it is not always possible to get rid of the foam.

How to clean the surface of hardened mounting foam:

1. Cut large pieces of sealant with a sharp knife.
2. Walk through contaminated areas with solvent, and be sure to apply the product exclusively on the foam.
3. Wait 20 minutes, gently remove the foam with a slightly damp cloth or cloth.

Important! It is necessary to be very careful when choosing a cleaner for dried foam, as it can be doubly dangerous for the surface on which it is necessary to eliminate the stain.

to contents ↑

How to clean clothes?

When using polyurethane foam, you should be very careful with clothes, since getting rid of dirt on fabric surfaces is the most difficult. You will have to cope with this problem on your own, since the dry cleaner does not want to take on cleaning clothes from building mixtures. Do not get upset and rush to throw out the smeared thing, because there is still a chance to save it. There are several ways to get rid of contamination on the fabric surface.

Cleaning instruction

Depending on the situation, you need to choose different cleaning methods. If the foam has not yet had time to harden, then first you need to collect it with a wooden stick, and then use a cleaner for not hardened foam.

How to act if the mortar is already frozen:

1. Cut large pieces of sealant with a sharp knife.
2. Walk through contaminated areas with foam cleaner.
3. Wait 10 minutes until the foam softens and remove with a brush. If not all areas have been cleared, then the action is worth repeating.
4. Walk the fabric with a slightly damp cloth or rinse under a warm stream.

Important! Powerful solvents and products that contain acetone should be used very carefully, because after use the color of the fabric may deteriorate or stains will remain that cannot be eliminated.

Cold

For thin fabrics, low temperature cleaning is suitable. To do this, you need:

1. Put dirty clothes in a plastic bag.
2. Put the bag in the freezer for a few minutes.
3. Using a knife, clean the thing from frozen sealant.
4. Remove remaining pieces using acetone-free nail polish remover or thinner.

Important! In a situation where nothing helps to remove pollution, creativity will come to the rescue. The main thing here is to soberly assess the amount of damage and come up with an original solution:

• The easiest way to find a marker of the desired tone, and draw a spot.
• Also, a solution to the problem is a convenient pocket at the site of contamination or a regular patch that can be bought at any fabric store.

to contents ↑

Sealant Cleaners

Each building mix manufacturing company also offers special cleaning agents, since the compositions of sealants of various companies have distinctive features. Of course, very often the means of other companies can also help, but it is better to choose a cleaner in accordance with the manufacturer, so that you do not have to worry for a long time with the foam removal process.

Acetone

Acetone serves as the basis for most solvents, so it can be independently used in its pure form as a cleaner from mounting foam. Do not forget that acetone is the most effective with a sealant that has not yet solidified.

Important! In order to achieve the expected result, it is necessary to use a foam cleaner several times. In this case, you must constantly change the rags, gradually reduce the concentration of the product. First of all, this applies to wood, leather and fabric surfaces.

Special wipes

Today, they produce special wipes for removing foam, which help to instantly get rid of hand contamination. When using such substances, it is important to be very careful.

Important! If you do not use special products, your hands will become clean within 5 days. In this case, it is better to use saline while washing hands, and to speed up the process, you can use pumice.

Popular professional cleaners

The most popular remedies are:

• The well-known manufacturer TYTAN offers both sealant and foam cleaner. This solvent does not damage the plastic of the window openings. If it is necessary to remove polymer droplets, it will be sufficient to use napkins moistened with a cleaner for this mortar.
• Cosmofen solvent perfectly copes with foam cleaning. This substance manages to immediately wash not only plastic, but also glass.
• When using Macroflex washing, a substantial softening of the sealed sealant occurs. This process greatly simplifies the wiping off of a contaminated site.

to contents ↑

Stock footage

Now you know everything not only about the types of polyurethane foam cleaners, but also about which of them and when to use. Stock up on such funds in advance, and then even in the event of unintentional contamination of clothing or decorative decoration of your home, there will be no problems with restoring its cleanliness.