Stainless steel sink faucet hole

It is impossible to name the absence of special openings for faucets or faucets in the sinks that are produced in our time, this is just a necessity. The fact is that the installation technology of such products involve several location options for the sink itself. The modern assortment offers several standard diameters for plumbing, so it is quite difficult to guess in advance with the size. It is better not to guess once again and not to risk it, but to figure out how to make a hole in the stainless steel sink for the mixer yourself.

to contents ↑

Varieties of modern sinks

The two main variants of kitchen sinks are most in demand today - stainless steel and ceramic products. Manufacturers are in no hurry to make holes in them, blaming this work entirely on the shoulders of sellers and end consumers.

Important! If you wish, you can agree directly in the store on drilling holes of the required size. The cost of such manipulation is quite acceptable, you only need to specify the place, diameter, make a payment. As a result, you will receive a finished product with decorated places for the installation of mixers and taps.

It would seem that the problem has been solved, but in practice, situations often arise that completely do not coincide with the plans of consumers. For example, when ordering a kitchen of non-standard sizes, or the kitchen equipment itself, if the mistress of the house is left-handed, the hole in her new sink is located on the right side, which is incredibly inconvenient for her.

to contents ↑

General recommendations for independent work

Cutting under the stainless sink mixer - how to do it? Before cutting a hole in the sink for the mixer, first install it, take a good look, and only then decide where to make room for the nests. If you still decide to do everything yourself, then use the following useful recommendations:

1. All manipulations with the product are carried out immediately before it is mounted on a stationary place - this will prevent premature damage and deformation of the object.
2. Install the sink horizontally on a wooden base, then drill a hole with a special drill.
3. In the case of using a punch and a hammer, it is enough to manually pierce the fixed bowl with special nozzles, selected previously for the diameter of the holes of the tap or mixer in a new sink.
4. If you want to use a punch of a special design, then note that it operates by the extrusion method. Typically, such a device consists of two nozzles and a threaded pin, a compression washer and a tap. It is enough to put the pin in place from the outside, screw the washer, make a tightening-pressing.
5. The use of a special drill involves the use of a cone-shaped drill, working according to the simplest principle.
6. When buying a mixer with large-diameter glasses, it becomes necessary to prepare a special landing socket. This problem can be solved in two ways - you can order a nest in the store or drill several holes around a circle with a smaller diameter.

to contents ↑

How to make a hole in a ceramic sink with your own hands?

It is quite simple to make a hole in a ceramic sink for a mixer yourself. The work includes the following steps:

• Mark in place of the intended hole, then drill.

Important! Such seemingly simple manipulation in practice causes many problems for inexperienced people. Here you can’t use a drill with a winning stand, because instead of drilling, peeling or chipping the material, it’s A metal drill has proved to be excellent here, but for it you will need a drill with minimum speed, preferably a manual one.

• Walk the tool several times through the partitions between the holes.

Important! Remember that when drilling ceramics can quickly heat up, so you need to control this. It is better to drill with a thin drill, work along the entire perimeter of the future nest.

• Cut the strokes with an electric soldering iron, hammer out the plugs with a hammer.
• Saw the material with a jigsaw so that the edges are perfectly even.
• Sand with a round abrasive nozzle on the circumference of the socket. If you don’t have it at hand, you can use the round file.

Important! Some modern bowls already have special marks, on which it is enough to aim with a hammer to pierce a hole. But it is recommended to do this as carefully as possible so as not to destroy the material.

to contents ↑

How to make a hole for the mixer in a stainless steel sink?

There are several proven options for how to cut a hole in a sink without a hole for a mixer made of stainless steel. In already installed plumbing, it is impossible to make such holes, since it can crack due to the support on the countertop. If possible, rent or buy a special cutter to make your job easier.

Prepare the following tools:

• Mounting tape.
• Marker.
• Round file.
• Hammer.
• Punch.

The instructions for making a hole look like this:

1. Before starting work, the sink should be turned upside down so that it abuts against the table surface with all edges.
2. Make a circle of the required shape and size from the mounting tape, attach it to the selected place, circle with a marker.
3. Mark the center to make it more convenient to punch a hole with a punch.
4. Point the point of the center punch to the center of the circle made of the mounting tape, punch the initial hole with smooth tapping movements.
5. Extend the opening with a round file to the previously defined size.
6. Thoroughly sand the edges of the saw to get the output of the required diameter.
7. Seal the edges of the fresh saw with sealant.
8. You can install the sink.

to contents ↑

Stock footage

Now you can cope with any material yourself, make a hole in the exact place where you are comfortable. It remains to carefully study the recommendations and instructions in order to fully present and visualize the entire process.