How to repair a Samsung washing machine with your own hands?

Long gone are the days when an automatic washing machine was a luxury item. Today it is one of the indispensable helpers of women in the household. Therefore, if the washer fails, the problem requires a quick and immediate solution. Of course, there are breakdowns that only a specialist can handle. But in many cases, you can figure out the cause of the malfunction yourself and repair the washing unit yourself. How to repair a Samsung washing machine with your own hands - this is what the article is about.

to contents ↑

How does a washing machine work?

Despite the huge number of models, the device of this technique is, in principle, the same, and the operation algorithm is the same:

• After you have loaded the laundry, selected the program and turned on the machine, the door automatically locks and the unit starts to work.
• The inlet valve opens, water enters the machine, the level of which is regulated using a special sensor. After the required volume of water enters the drum, the valve closes.
• Water is heated to the desired temperature with the help of a heating element. Water heating to a certain temperature is controlled by a special sensor or timer.
• While the electric water heater is working, the drum automatically rotates in different directions. It is necessary that the laundry is evenly wet.
• After the water has warmed up to the set temperature, the heating element is switched off and the washing process begins. In this case, the drum rotates in different directions with equal time intervals. This is necessary so that the laundry does not stray into a solid lump when washing.
• At the end of the washing algorithm, the pump pumps out dirty water, and clean water rinses. When rinsing, the rotation of the drum occurs at low speeds. Depending on which washing mode you have chosen, there may be several rinses.
• After the laundry is rinsed, the pump pumps out water.
• The spin mode takes effect. The drum starts spinning again, but with a large number of revolutions. During the spin cycle, the pump is turned on and off until the complete wash program.

As you can see, there is nothing particularly complicated. Therefore, to understand why the washing machine failed, you need to find the node in which the breakdown occurred. Since all washers work on the same principle, all malfunctions are similar to each other, like twins. Consider the most common problems, their causes and solutions. This will help you navigate and understand how to repair a washing machine yourself.

Important! On our site of useful tips there is another article related to malfunctions of Samsung washing machines and their solutions. Follow the link to learn more aboutSamsung washing machine error codes, their decoding.

to contents ↑

The washing machine does not turn on

So, you want to wash, turn on the unit, and he - in general, “died”, and does not show any signs of life. The reasons for this trouble are many:

• The simplest is that the washing machine is not plugged in.
• The washing machine will not work if the door is not closed tightly enough. As a rule, electronics immediately react to this with a light signal on the board.
• The machine may not turn on even because the washing program is selected incorrectly.
• If all of the above issues are excluded, then possibly the electrical part of the machine is faulty.
• At the same time, do not forget to check the automatic relay: whether it was knocked out from voltage surges. Find out from our separate post,why does the machine knock out when the washing machine is turned on.
• Did not find the reason here? Check the condition of the outlet. Maybe she’s out of order?
• After checking the outlet, at the same time inspect the plug, make sure that the contacts are in good condition.
• Is everything okay? Unplug the power cord and ring the power cord. To check the condition of the terminal connections, remove the external panels of the machine.
• Another reason that the washing machine does not show any signs of life is the closed inlet valve. If you set it to the “open” position, water begins to flow into the drum, and the technique magically regains its former performance.

As you can see, a large-scale repair of the Samsung washing machine or any other brand is not required here, although for the initial symptoms you can start to panic, thinking that the problems are significant.

to contents ↑

Machine typed water but doesn’t erase

The reasons for this phenomenon may be the following:

• Blown heater. If the heater does not function, the washing algorithm fails and the machine does not function. Miracles do not happen: TEN will have to be replaced.
• The belt drive was worn and torn. To notice this breakdown, you have to disassemble the unit completely.
• The temperature or water level sensors broke.
• The processor is out of order. The machine does not receive commands and has no idea what exactly it needs to do. In this case, only a qualified craftsman can repair the Samsung, Beco, Indesit or any other washing machine. As a rule, a replacement control unit is needed.
• The inlet valve has broken. It is possible that it is clogged, and therefore does not open or close well. The situation is saved by cleaning the valve and installing an additional filter for water purification at the inlet.
• The electric motor burned out. Of all the breakdowns, this is the most unpleasant, fraught with expensive repairs. If you do not have experience rewinding electric motors, you will have to contact a service center.

to contents ↑

The machine does not pick up water

Or, alternatively, gaining it too slowly. Faults in this case can be as follows:

• The water supply valve is closed. Repair of automatic washing machines in this case is not needed. Open the valve and everything is in order.
• The inlet hose is clogged or deformed. The problem can be solved by straightening and cleaning the hose from blockage.
• Inlet filter clogged. To clean it from contamination, block the water, disconnect the hose and rinse the filter under a powerful water stream. After that, assemble the structure, acting in the reverse order. To avoid clogging the filter of the washing machine, if the water quality is poor, select the correct filter for washing machine.
• The intake valve is clogged and broken. In this case, you need to replace it, having previously blocked the water.
• The water level regulator has broken. In this case, no water is drawn into the drum.

Important! Sometimes the reason for slow water intake is low pressure in the system. This is not a breakdown, so no repair is needed here. With the normalization of water pressure in the system, the problem disappears by itself. If lowering the pressure in the system is a common thing, then it is advisable to equip a pressure tank in the attic of the house or under the ceiling of a city apartment.

to contents ↑

The machine stops in the middle of washing, the process is not completed

This may occur for the following reasons:

• Clogged system. Drain, clean the outlet and inlet hoses and all kinds of filters.
• No power supply. In this case, the algorithm is normal: check the plugs, automatic relay, serviceability of the socket, cord and contacts.
• Wrong wash mode selection. Sometimes a program includes a pause, and you only need to wait a bit. Repair Samsung washing machines with your own hands you do not need.
• The pump is broken, water is not pumped out, the washing process is disturbed.
• The water pressure in the system is low. Make sure that the water pressure is really insufficient, pause the program and wait until the wash resumes.
• The heater burned out, the thermal relay broke. As a result, the water does not heat up to the desired temperature, the program is knocked down.
• The outlet hose poisons and the water drains all the time. In this case, the system pumps water into the drum to the required level. At the same time, the processor “thinks” that the required amount of water has not been collected. To resolve the problem, check the quality of the outlet hose connection to the drain.
• The control timer is out of order. For a typewriter it is not clear when the time of one operation ends and the execution of another begins. Do not repair the machine with your own hands in this case - contact the service center.

Important! Another reason - an electric motor burned out. Doing the engine repair of the washing machine with your own hands is unlikely, it is advisable to contact the master.

to contents ↑

Bad spin

The most common cause of poor spin is clogging of the drain system. The problem is solved by cleaning the filter: removing hair, small objects, threads, tissue fibers.

Did the cleaning not help? The pump may have burned out and is not pumping water out of the tank. If the water drains normally, but there is no spin, the drive belt may have worn out. To fix the problem, replace it with a new one, or just tighten it.

to contents ↑

Drum does not rotate

How to fix a drum in a washing machine? The following options are possible:

• Pause in the program. You just have to check the selected mode.
• Wear or slipping of the drive belt. Using a special mechanism, tighten, or, conversely, loosen the belt.

Important! If the equipment is not equipped with a tensioner, then you can solve the problem by replacing the belt.

• Ring the electric motor. Perhaps he is out of order.
• Broken boot latch. In this case, you need to call the master and he will replace the castle.

to contents ↑

The hatch of the washing machine is jammed

The reasons may be the following.

• The washing program is not finished yet, the drum continues to rotate, and the hatch does not open. Wait 1-2 minutes after completing the wash program. The lock will open freely.

Important! The standard waiting time after completing the entire wash cycle is about 3 minutes.

• There is water in the tank. The program of many washers is designed so that until all the water leaves the tank, the door will not open. To fix the problem, drain the water forcibly, check the drain filter for clogging. After cleaning the filter, the problem will be completely resolved.
• The lock switch is out of order. He needs a replacement.

to contents ↑

The machine works with rattling and noise

• The nature of the malfunction can be determined by the sounds that the unit makes: A metallic sound or uneven rattling indicates that metal objects got into the washer: nuts, keys, coins, etc.
• If the sound resembles a buzzing noise, inspect the latch. Perhaps she is broken.
• A screeching sound indicates that the drive belt is slipping. If the belt is tightened, then the unpleasant buzz disappears.
• Does the machine work with a knock and bang? Most likely, the bearings are worn out. They urgently need to be replaced.

Important! If this is not done in time, the shaft will be broken, and repair of automatic washing machines will be much more expensive for you.

to contents ↑

Water is flowing

To understand where the leak came from, wipe the floor around the machine dry and lay a dry rag under it. Turn on a short wash without laying laundry or using detergents. You will be able to see which side water flows from the unit.

Causes of leaks can be.

• Hose cracking.
• Loose clamp.
• Gap or skew of a sealant on a door.

Important! If it turns out that all the details are working, perhaps the reason is the clogging of the sewer. Water simply has nowhere to go.

to contents ↑

Water does not heat up:

• The most common problem is the burnout of the heating element. Often TENy burn out from the fact that insoluble plaque accumulates on them. Find out,how to remove scale in a washing machine. If the heater burned out, it must be replaced.
• Sometimes the water level regulator fails. The machine does not receive information that the water has already accumulated, and the heater does not turn on.
• Another common cause is a broken thermal relay. The heater is turned off before the water is heated to a predetermined temperature.

to contents ↑

No water drain:

• The most harmless reason is the wrong choice of washing mode. If the switch is in delayed rinse mode, the reason is clear.
• It may also be that the wash stopped due to a lack of electricity.
• Water may not drain due to clogged drain pipe or filter. Drain starts to work normally after cleaning these components.
• Water may not drain due to blockage or pump malfunction. In the first case, it must be cleaned, in the second - replaced.
• Lack of water discharge occurs if the electrical part is faulty (failure of the timer, oxidation of contacts, the water level switch has broken).

Important! If in the process of ringing any of the listed parts is found to be faulty, then the repair of automatic washing machines consists in replacing a failed part with a working one.

to contents ↑

Strong vibration, “jumping”

The most common reason that the washer “goes for a walk” is a strong tank overload.

Important! It is important that you load no more than the instructions provided. Sometimes it happens like this: there are few things, but they have gone astray. This problem happens in obsolete inexpensive models.

If we talk about modern models, then the reasons may be as follows:

• Sometimes the reason for “jumping” is because the spring that holds the drum broke.
• It happens that the weights of the counterweights are loosened. All this leads to an imbalance of the structure.
• If the floor is uneven, and the machine is not installed at the level, then it may well “start dancing”.

Important! The position of the washer can be adjusted using the legs with adjusting bolts. If this is not enough, use pieces of durable cardboard.

to contents ↑

Breakdown prevention

You can repair the washing machine, either by the service center or independently. But how to make your assistant please you with stable work as long as possible? To do this, follow the simple rules:

• Using the machine, do not forget to periodically look at the instructions. Without knowledge of the device of the LG washing machine, repair is hardly possible.
• Avoid overloading the unit.
• Use detergents containing water softeners.
• Once every 3-4 months, start the wash cycle without powder and things, but with a descaling agent. It can be ordinary citric acid. Read how to use it in our separate review. "Citric acid for a washing machine".
• Clean the inlet and outlet filters of the machine.
• When loading things into the car, check your pockets for foreign objects.
• Do not stint on the purchase of a voltage stabilizer.This is a good protection of the electrical part of the machine from power surges.

to contents ↑

Stock footage

If you follow these simple measures, repair of the washing unit will be rarely needed.