Indesit washing machine malfunctions

Indesit brand washing machines are by far one of the most popular. Such a demand is associated with their high quality at a fairly budget price. Unfortunately, like other equipment, this unit can also fail from time to time, which creates huge inconvenience to its owner. Therefore, so that you do not wait for weeks until the repair in the service center lasts, we will tell you about the main malfunctions of the Indesit washing machine and how they can be eliminated at home.

to contents ↑

Features of repair of the Indesit washing machine

Almost all modern models of washing machines of this brand have in their configuration a special diagnostic system, which is built into the general power supply system as a separate module. Therefore, in the event of any malfunction, the machine displays an electronic code of the error on the LCD screen. Accordingly, to eliminate it, you only need to open the instructions, find the error displayed, then, following the manufacturer's recommendations, determine the type and place of the breakdown, as well as eliminate it.

Important! Pay attention to the fact that it is not recommended to start an independent repair of the washing machine if its warranty period has not yet expired. In this situation, it is advisable to call the wizard from the service center. Otherwise, you may lose the free warranty service, and you will have to pay a tidy sum of money for repairs.

If smoke begins to flow from the device during the washing or spin cycle, this means that the breakdown of the device is quite complex, so you will need to check the operation of all systems using special equipment. Unfortunately, in this case, you also can not do without the help of a specialist.

to contents ↑

The main and most common breakdowns

We bring to your attention the main types of malfunctions that are most often encountered during the operation of Indesit washing machines:

• The output of the heater. Unfortunately, unlike the more expensive brands, the heating elements of the Indesit washing machine are not opened with a special protective coating. Accordingly - in connection with low-quality hard water and improperly selected detergent, it begins to accumulate salt deposits on the surface and fails.
• The surge protector burns out. This is the weak link of the Indesit washing machines. There are even such cases when these units are sold already with a defective surge protector, respectively - they are subject to warranty replacement.

Important! The surge protector, as a rule, with proper operation in compliance with all manufacturer's recommendations should be changed once for 3-4 years.

• Broken bearings. This problem is typical for both budget and rather expensive washing machines. As for devices of the Indesit trademark, in this case the replacement of bearings may be accompanied by some difficulties due to the inaccessibility of the assembly.
• Failure of the control unit. This type of failure in relation to others occurs less frequently. This is due to the fact that every year the manufacturer equips the unit with more modernized versions of control units.

Important! In order to avoid possible breakdowns, you should carefully study the instructions for use of the Indesit washing machine of a particular model. Sometimes manufacturers provide brief information that does not describe all the step-by-step actions of the user. Recommended to study detailed instructions for washing machines Indesit, which will quickly help you in a particular situation.

to contents ↑

How to troubleshoot correctly?

In order for you to find out the type as accurately as possible and find the cause of the malfunction of the Indesit washing machine for its further elimination, experts recommend that you follow this sequence of actions.

1. If the model of the washing machine is equipped with a liquid crystal display, in this case it is best to wait until the unit itself displays an error code for you. The device can detect such an error in the process of self-diagnosis, after which it can be eliminated, based on the manufacturer's recommendations specified in the instructions.
2. If the device does not have a self-diagnosis function or if it malfunctions due to a breakdown, you need to conduct an external inspection of the device and check whether it makes any unusual sounds during washing. For example, if the bearing has fallen into disrepair, the device will begin to emit an unusual rumble or knock, which is especially audible during the spin cycle. If there are any problems with the heater, you can find such a breakdown by such signs as a cold manhole cover, the remaining insoluble granules of the washing powder, as well as a significant decrease in the quality of the wash.
3. If the previously listed measures were unsuccessful, in this case the washing machine must be disassembled. You should start directly by dismantling the line filter, after which it is necessary to check the power supply on the contacts using a tester. The cause of the breakdown can be considered detected in the event of a complete lack of power.

Important! If you did not find any problems with the line filters, you should check the power in all elements of the device, and thoroughly inspect the parts and mechanical components.

It should also be remembered that sometimes an independent repair of an Indesit washing machine cannot do without additional special tools, such as:

• Phillips and flat head screwdrivers;
• Nippers;
• Pliers;
• Pliers for clamps;
• Flat wrench;
• Service hook.

to contents ↑

Do-it-yourself Indesit washing machine module repair

Before proceeding with a direct repair, you should study in detail the device with which you work in order to determine the breakdown and eliminate it. The main symptoms of a module malfunction are:

• Bad spin;
• Lack of illumination of indicators on the panel;
• Untimely discharge of water;
• At a previously set time, the wash cycle does not end;
• Lack of rotation of the drum;
• The work of the programs you specify occurs with various violations;
• Inconsistency of the temperature regime of the cycle you specified.

If there are such signs, the module of the Indesit washing machine is to be repaired. Most often, they perform its replacement or do a complete flashing of some elements of this device.

Important! If the microcontroller fails, a new board should be installed.

How to check and fix a module breakdown?

In order to repair the module, it is necessary to find out the reason that led to its malfunction. The main ones include:

• Marriage approved by the manufacturer. It occurs immediately after the first few times of operation and is eliminated exclusively by warranty repair.
• Poorly welded tracks and other elements lead to a malfunction of the device circuit.
• Frequent voltage drops. They negatively affect the operation of the washing machine and lead to its damage.
• Moisture inside the washing machine.

Important! In the event of a malfunction of the washing machine, the display will show a code that has a certain decryption. Read the detailed instructions that indicateerror codes of Indesit washing machines, their designation and remedies.

Repairs:

• The knob that is responsible for switching programs does not respond or moves freely. Repairing it is quite simple, just blow the sensor for this. If this does not help, then the program shift knob should be replaced with a new one.
• Burned contact groups, which are located on the surge protector. Basically, this malfunction is a privilege of older Indesit washing machines. This is due to the fact that during operation there is an accumulation of burning. You just need to remove it from the contacts. Thus, the problem will completely disappear.
• In case the locking lock has broken, you better just clean it.
• Belt loosening is the main cause of a breakdown in the washing machine module. In order to eliminate it, the device must be disassembled, and the belt - tightened. If your efforts were unsuccessful, then the belt should be replaced with a new one.
• In the event of moisture getting into the device or poor grounding of the outlet, the module will need to be replaced with a new one, since repair in this situation is already quite problematic.

to contents ↑

Damage to the heating element, line filter and engine sensor

If the line filter fails, it should be replaced immediately with a new one.

Important! Pay attention to the fact that even buying and replacing a power strip with a new one does not guarantee you that it will last for a long time, even if your power supply is without voltage drops. The reason is the condensate that forms on the contacts, as a result - a short circuit occurs inside the device itself.

In order to extend the operating life of the line filter, the contacts must be cleaned and wiped thoroughly with a clean and dry rag, then pour them with silicone-based sealant. In this way, you can isolate other contacts that are subject to moisture.

As for the breakdown of the capacitor in the engine circuit, this is a rather significant problem, and attempts to fix it on their own can only lead to an aggravation of the general situation.

Important! If you do not have any experience in the repair of Indesit washing machines, if a capacitor is broken, you should contact a service center immediately. This is due to the fact that the signs of this breakdown are very similar to those that are observed when the motor breaks down. Only an experienced specialist can recognize them.

Another problem is the use of collector motors. They have a low price, but at the same time have high reliability. These motors are equipped with brushes, which are periodically subject to replacement, so that in the future there would be no malfunction during operation of the washing machine.

As for the replacement of the heating element, this process is within the reach of even a novice. You just need to adhere to the following procedure:

1. Unscrew the fasteners, then remove the back of the device.
2. On the two contacts that protrude from the bottom of the tank, find the heater itself.
3. Check for power to the contacts using a tester. If the power is normal, this means that the heater has burned out and must be replaced.
4. Unscrew the centrally located fastener.
5. Remove the rubber seal, and then remove the heater itself.
6. Install a new heater.

to contents ↑

Bearing troubleshooting

It is quite easy to solve the problem with bearings, especially in the first models of Italian production. In order to gain access to the bearing assembly, the following procedure must be followed:

1. Drain and unplug the device.
2. Remove the back and top panels.
3. Remove the belt and lock the drum with the clamp.
4. Disconnect the thermostat wire and remove the screws that secure the bearing assembly. Be prepared for the fact that this operation can be difficult for you.
5. Loosen the clamp and remove the tank cap with seal.
6. Fit an interference bearing on the drum axis. Remove the worn out spare part and an epiploon then establish a new.

Important! To dismantle the bearing, you need to prepare such a tool as a puller in advance, since without it this operation will be quite problematic.

As for the new models of Indesit washing machines, the drum is made integral in them, so it is impossible to get to the bearing. The manufacturer suggests that in the event of such a malfunction, the device should be disposed of. Unfortunately, not everyone can afford such waste, so engineers at service centers have found a way to carry out such repairs. To do this, the tank is simply cut along the weld. Thus, free access to all necessary elements appears. After replacement, the washing machine is assembled and a trial run is made. If everything is done correctly, then it will work without malfunctions and extraneous noise.

Important! Please make sure that no water leaks out of the Indesit washing machine during a test run. If leaks nevertheless appeared, the device must be disassembled and reassembled. You may also need to replace the seals.

to contents ↑

Repair control unit for washing machine Indesit

Malfunctions of the control unit that arise due to power surges should be eliminated exclusively with the help of specialists, since it may be necessary to completely replace the processor itself, which is not enough for beginners. You can repair the main board yourself only if condensation has formed on it, which can cause a short circuit.

to contents ↑

Fix Indesit Washer Problems

Earlier, we listed the main problems that arise during the operation of washing machines of the Indesit trademark. Unfortunately, these devices are not safe from ordinary breakdowns, which are characteristic of absolutely all washers. Therefore, so that such situations do not catch you by surprise, we will tell you what to do if they arise.

Waste water does not drain:

• The simplest cause of this failure is a clogged drain system. In order for the device to work again without failures, you just need to remove the accumulated dirt.
• It is much worse if the pump itself directly fails, which carries out the pumping of water. This can occur due to overheating of the motor, as well as a short circuit in the winding. In this case, you will have to replace the motor with a new one.
• Another reason for the lack of discharge of waste water is the deformation of the plastic pump casing, as a result of which it clamps the impeller blades. In this situation, it is advisable to replace the pump casing with a new one, or if there is no such possibility, simply cut the impeller blades with a sharp knife.

The lock on the hatch has stopped working

Such a malfunction of the Indesit washing machine can lead to the fact that the device simply stops turning on. This is due to the fact that there are contacts in the lock, and if something prevents it from closing, power is simply not supplied to the units of the unit, so the mechanism fails.

Important! Pay attention to the fact that in most cases, the cause of the malfunction of the castle is the dirt accumulated in it. Therefore, in order to eliminate it, you just need to clean the lock.

Drum belt loosened

First you need to try to tighten this belt. If this failed, it must be replaced with a new one.

No water enters the washing machine:

1. If such a malfunction is formed, the first thing to do is to check the pressure of the water supply by opening the taps.
2. If it is normal, check the hoses through which water enters the device for depressurization or simple clamping.
3. If everything is okay with the hose, the cause of the malfunction may be the coarse filter. Therefore, in order to resolve the problem, it should be subjected to deep cleaning.

Important! A fairly serious breakdown of the water supply to the device is considered to be a cut-off of the level switch. Only a specialist of a service center can eliminate this problem.

to contents ↑

Stock footage

As you can see, repairing an Indesit washing machine with your own hands is not always difficult. Following the advice of our specialists, you can easily find and recognize the cause of the breakdown, and then eliminate it as soon as possible.