DIY Bosch Max 5 washing machine repair

Buyers have long loved Bosch appliances for its quality. The washing machines assembled in Germany are admirable: they have excellent ergonomics, and the materials going to the assembly are of the highest quality. But this technique can also break. Therefore, users should know how to repair a Bosch Max 5 washing machine with their own hands. We will talk about this in this article.

to contents ↑

Diagnose faults

In modern models of Bosch equipment there is a special program due to which it is possible to identify equipment malfunctions without resorting to the services of a wizard. Usually, the terms of use contain information on how to use the program. And we will consider the testing algorithm of the machine if the drum stops spinning:

1. Close the door of the loading door.
2. Turn the program selection knob to the “Off” position.
3. We expect 2-3 seconds.
4. We transfer the handle to the "Spin" position.
5. We are waiting for the start button to flash, located on the control panel.
6. Press and hold the spin button.
7. We are waiting for the “Start” button to flash again.
8. We transfer the handle to the Drain mode.
9. Release the button “Spin speed”.
10. The display shows a code that identifies the fault.

Important! If it was not possible to start the diagnostics of the washing machine, it means that the system board is faulty.

To start the engine test, the mode dial is set to “3”. After it is installed in position “4”, the drain pump will be checked, and in position “5” - the heater. Positions “6” and “7” start the diagnostics of cold or hot water inlet valves, positions “8” and “9” - test the water inlet valve during the main and preliminary washings.

to contents ↑

Frequent breakdowns

The masters determined that the following faults can most often be found:

• Lack of heating water during the washing process;
• Lack of discharge of water;
• The drum does not rotate;
• The presence of noise inside the drum;
• Lack of a set of water;
• The engine does not start.

Important! Based on this list, we can conclude that the most common problems relate to the heating element. When burning a heating element, but remaining in the integrity of the electronic system, a lot of time and effort will not be spent on repairing the Bosch washing machine Max 4 or 5 with your own hands.

Also find out from a separate publication,where is the Bosch washing machine. 

to contents ↑

Why breakdowns occur?

Each malfunction has its own reasons. Consider them more closely.

Situation 1

If there is no water drain after washing, the reason may be:

• Damage to the drain pump;
• Faulty contacts between the power supply and the pump;
• Blockage of the drain pump or filter;
• Damage to the water level sensor.

Situation 2

If the drum stops, damage may occur due to:

• Wear of the drive belt;
• Engine breakdowns;
• There is a problem in the electronics or control board.

Situation 3

The lack of water intake in the tank is due to the fact that:

• There is no water in the water supply;
• The pump or the Aquastop system is clogged;
• The drain hose is broken.

Situation 4

Noise may appear inside the drum due to:

• Defective bearings;
• Stuck in a drum of a small object;
• Damage to shock absorbers;
• Torn off counterweight.

Important! The engine may not work because the electronics are broken or the sunroof is not closed. After finding out the cause of the malfunction, you can proceed to resolve them. In the event that the failure could not be determined, it is worth contacting a specialist.

to contents ↑

DIY machine repair

If you decide to repair the Bosch Max 5 washing machine with your own hands, prepare the necessary tools. Consider the repair of simple faults.

Drain filter clogging

It can be found at the bottom of the machine, under a cover or panel. The lid gently opens clockwise, the filter is pulled out and washed under running water.

Important! Before repairing the filter, do not forget to put several rags under the machine that will absorb water.

Water Level Sensor Replacement

You can find this spare part in the right corner under the top cover. To remove the cover, two self-tapping screws are unscrewed from the back. To pull out the sensor, press the latch. After this, remove the hose and disconnect the contacts. Next, you can install a new sensor.

Replacing the heater

Such repair of the Bosch washing machine Max 4 or 5 with your own hands is also quite realistic to do. The heater is located below, under the tank. You can see it by getting rid of the back cover. To replace, perform the following steps:

1. We unscrew the bolt that secures the heater to the tank.
2. Disconnect the wires.
3. We take out the heating element.
4. Insert a new heater.
5. We assemble in the reverse order.

to contents ↑

Stock footage

Do it yourself, you can repair many breakdowns in washing machines. Most often, instructions can be found on the Internet, where they are detailed and with a video. Most housewives can handle most repairs. So if the damage is not very difficult, go for it!