Ariston washing machine - error f 08
Any mechanism - both the simplest and the latest generation electronic, can sometimes fail. And if this is a complex system such as a washing machine, it is necessary to deal with possible malfunctions very responsibly, scrupulously and carefully. We will analyze the situation if the Ariston washing machine, error f 08, or some other programmed by this manufacturer.
to contents ↑The most common mistake is its causes and solutions.
Very often, people are faced with the phenomenon that they see the error f 08 on their Ariston washing machine. This combination of symbols that indicate a malfunction of the equipment is most common.
The reasons for its occurrence:
- The relay of a tubular electric heater (hereinafter - TEN), which heats the water itself, is cut off.
- The sensor is stuck in the full position.
Here's what you need to do if you see a similar problem:
- First of all, we check the water sensor (in other words, the pressure switch).
- Then check the heater. Usually, its connection to the electronic controller is checked. If any malfunction is detected in the part - the heater is completely replaced.
- If everything is in order with the heater and the water regulator, then the electrical controller itself is replaced.
Important! In 8 out of 10 cases of the occurrence of the error f 08 on the Ariston washing machine, it is necessary to change the heater. Find out how in our separate review “Repair of washing machines - replacement of heating elements”.
If the failure in the SM Ariston system with the error f 08 is not resolved, we advise you to take your car to the master to a service center or call a specialist at home. He will surely be able to repair your assistant so that she does not break for a long time.
to contents ↑Important! Most problems with the washing machine can be avoided by conducting it in a timely manner. prevention and protecting the electronics of the equipment from voltage surges surge protectors.
Other Ariston washing machine malfunction codes - their causes and solutions
In addition to error f 08 in the Ariston washing machine, there are many more problems and causes of equipment malfunction. Let's try to analyze the causes of manifestation and methods of dealing with each of them.
f 01
Most often, such an encoding appears if a short circuit occurs in the power circuit in conjunction with the CM drive motor.
Solution: in most cases, you need to replace the controller with the drive motor.
f 02
The response of the tacho cannot arrive at the electronic controller.
Remedy: Check and replace the drive motor.
f 03
The problem with the heating sensor or, like the error in Ariston f 08, the heater is faulty.
Repair method: replacing the regulating element itself, and if necessary - control module.
f 04
The problem with the pressure switch. This situation is also similar to the one at the beginning of the article.
Correct: we need to replace the electronic controller along with the level sensor.
f 05
When displaying such a combination of characters, drain pump malfunction.
Necessary repair measures: replace the pump itself, pressure switch, electrical controller, and possibly all at once).
f 06
If the Ariston washing machine produced such a combination, sticking or another reason for the failure of certain buttons occurred.
A way to restore the functionality of the system: it will be necessary to replace the control panel and the electronic module for adjusting the operating modes of the entire system.
f 07
With this code, the heater is not immersed in water, which means it cannot heat it.
Remedy: replace the electronic controller, if necessary, also a heater (depending on the model of the control unit).
f 09
EEPROM memory issue.
Repair: replace the electrical controller, the master can rewrite the non-volatile memory circuit.
f 10
Most likely, the level sensor does not work (there is not enough water poured).
Solution: replacing the defective part of the water level adjustment and the electric controller (depending on the model of the control unit).
f 11
With this coding, a signal is received that the drain pump is disconnected or cut off.
Remedy: Typically, the drain pump and the electronic control unit need to be replaced.
f 12
The reason for this set of characters on the display is that there is no communication between the controller and the display module.
A way to restore the health of the Ariston washing machine with this error: replacing these two parts.
f 13
If you see such symbols on the display, there is a problem with the drying mode.
Remedy: replacing the drying control sensor and the electronic module.
f 14
Drying cannot turn on, therefore the Ariston washing machine gives an error with such symbols.
Repair takes place according to this principle: they replace the most complex element - the control unit, and the heater, which dries.
f 15
The problem is directly opposite to the previous one - drying cannot turn off.
Remedy: replacing the level sensor and sometimes the backplane.
f 17
In this case, the hatch cannot close.
The way to solve the problem: replacing the door lock with a lock and the electronic control module.
18
One of the most difficult causes is a microprocessor failure.
As a rule, it is only possible to replace the electrical controller to restore the correct operation of all equipment. Be prepared for the fact that you will have to pay a substantial amount of money for it, as for the services of the master. Doing it yourself is highly undesirable.
to contents ↑Important! Any malfunction of this technique, whether it is an Ariston f 08 error or any other described above, requires the repair of an experienced craftsman.
Stock footage
So, in this article we figured out the main causes of the errors of the Ariston washing machine and proposed solutions to each of them. However, we do not recommend repairing the car alone if you do not have practical experience. So you can break it completely.
(No ratings yet)
Loading...
