Electrolux washing machine - malfunctions, DIY repair

In fact, everyone knows the name of the Electrolux company, but few are familiar with the technology of this company. In this article we will talk about the technology of this company in more detail. And more specifically - we’ll talk about the “Electrolux” washing machine - malfunctions, DIY repair. Each owner of a washing machine of this brand is strongly recommended to read the instructions for use. This is necessary in order to restore the operability of equipment in case of failures.

to contents ↑

Symptoms of car breakdowns

External manifestations of malfunctions of the washing machine - these are the symptoms. They can even be such trifles as working a little longer than usual or a slightly altered sound. All this indicates that something is not working properly in the washer. Thanks to such things, we detect a breakdown and manage to restore the equipment.

Important! The big problem is that some malfunctions appear before such symptoms appear, and the worst is that they do not manifest themselves for a long time.

The most common symptoms are:

1. Wash in cold water. Water does not heat up, even if otherwise specified in the program.
2. Water is not poured.
3. Water does not drain.
4. Rinsing is not performed in two versions: either it does not go to it at all, or it skips and performs the following actions.
5. There is no spin.
6. No powder is taken from the cuvette, and washing occurs without it.
7. It does not turn on or turns on once.
8. When you turn on the machine, the machine knocks out.

Important! A common cause of machine breakdown is hard water. The negative result of contact of such water with the mechanisms of the machine is scale, mold, unpleasant odor, etc. This can and should be fought. Read more in our articles:

• Cleaning the Beliznoy washing machine;
• How to clean a washing machine with vinegar?

Now that we’ve figured out what situations to watch out for, and possibly repair the Electrolux washing machine with our own hands, we’ll talk about the situations in which certain actions are necessary.

to contents ↑

The machine does not flood

The washing cycle in any washing machine - “Electrolux” is no exception, it assumes that the water will merge and fill. At least twice - when washing and rinsing. Water is also drained after spinning and drying.

This is where the obstacle arises. If it cannot fill the water, then the program freezes and the wash stops.

Important! In this situation, the manufacturer has provided a system of errors that are displayed on the display in the form of a special code. You can decrypt it by looking at the instructions. In particular, if the situation we are discussing arises, the machine displays the code E11.

Causes

If your device issued an E11 code, there may be 3 reasons:

1. No water supply.
2. The filling valve does not work.
3. The filter that is installed in the inlet hose is clogged.

Decision

What to do in this case? Since there are several reasons, you need to start from the most obvious.In our case, the first thing to do is to check the presence of water in the tap, because if there is no water, then you can make the obvious conclusion that the breakdown is not in the car.

Second, check for clogged filter. You need to do this like this:

1. Check if this filter exists in your washer.
2. If it exists, then shut off the water in the risers, carefully remove this filter.
3. Assess the degree of contamination and find out if the filters on your washing machine model are cleaned.
4. If the filter is cleaned, remove the blockages and put them back.
5. Otherwise, you have to buy a new filter.

Important! Do not forget that in all washing machines, sooner or later, the replacement of such a filter is required. Otherwise, it will become clogged so that it stops the water supply.

If you find that the reason is not the lack of water and the filter, then you have to deal with the inlet valve. To conduct its verification, you will need to use a multimeter. If you still haven’t found a problem, you will need to contact a service center.

Important! Sooner or later, all the equipment wears out physically. In the event of a serious breakdown, repairs can be very expensive. It often happens that parts of your washing machine model are no longer available. It's time to think about buying new equipment! For you, we have prepared the ratings of the best washing machines:

• TOP of the best front-loading washing machines;
• The best top-loading washing machines.

to contents ↑

The machine does not drain water

In a situation where water is poured but not drained, the washing program is activated, but rinsing does not occur due to the fact that the water does not leave the tank. The problem may be due to the following reasons:

1. Malfunction of the drain pump.
2. Drain hose clogged.

Replacing the drain pump is easy - just follow the instructions. The same situation with the hose. We’ll start with checking the hose. For this:

1. Drain the water tank through the emergency drain hose. In most models, it is located at the drain filter in the lower right corner of the washer.
2. Next, disconnect the drain hose from the product drain pipe or siphon.
3. Clean the clogged Kursk wire or with a special cable.
4. Rinse it with running water.
5. Put the hose in place, check the operation of the device.

to contents ↑

The machine does not pick up powder

Let's move on to another malfunction of the Electrolux washing machine and do it yourself repair. The main symptom of such a malfunction is a deterioration in washing quality over the years. As it turns out later, the whole problem is that the washer does not pick up the powder from the cuvette. Washing comes out almost without powder, therefore the quality of washing leaves much to be desired. What is the reason for this situation? Let's consider in more detail.

Causes

During normal operation of the washing machine, a stream of water must pass through the powder compartment, which takes all the contents with it. This water passes through the valve, which should open at the beginning of the set mode. But when it is already worn out, clogged with water stone and dirt, it may not open. This is the reason for this malfunction.

Decision

To repair the Electrolux washing machine with your own hands:

1. Pull out the detergent drawer.
2. Remove the top of the washer.
3. At the base of the niche where the powder compartment was located, find that valve, inspect it.
4. If it is damaged, it must be replaced. If you can just clean it, clean it.
5. Replace the cover, insert the powder compartment.
6. Check the operation of the washing machine.

As you can see, sometimes due to a simple valve, such a small part, the whole system may not work well.

to contents ↑

The washing machine does not rinse and does not squeeze

If your system does not squeeze or rinse products even when a special program is specified, most likely these are problems with the control board. Its breakdown can not be fixed with your own hands.Therefore, in order for you to repair the control board, you will need to contact the service.

to contents ↑

The machine does not turn on

If you can not only start the wash, but just turn on the appliance, there is probably a problem with the power button or the network cable. There is also the possibility that there is simply no electrician in the house. Therefore, it is worth checking it out.

Decision

In order to check the version of the causes of the breakdown, you need to use a multimeter, or more precisely, measure the resistance values ​​on the button contacts and the wires of the network cable. In order for you to access the power button, you must:

1. Remove the powder compartment.
2. In the niche that opens on the right side, unscrew the fastener that holds the instrument panel.
3. Do the same with the remaining bolts and remove the panel.
4. Detach the plastic holders that secure the front.
5. Find the contacts of the power button, measure the value.
6. If the problem is in the contacts, then they need to be cleaned and soldered, and then assemble the machine in the reverse order.

If the button is in perfect order, then, most likely, there is a problem with the network cable. It is also possible to repair the Electrolux washing machine with your own hands. For this you need:

1. Remove the back cover of the washing machine.
2. Disconnect the protective gasket from the base of the power cord.
3. Check the connection of the wires of the network cable with the contacts of the network filter.
4. If the wires are fixed securely, then disconnect the wire and check it with a multimeter for a breakdown.
5. If you find a broken wire, then it must be replaced with the original new one.

At the end, reassemble the washer, check its operation.

Important! When working with the power cable, do not plug it into an outlet to avoid electric shock.

to contents ↑

If the machine is knocked out

In the event that your assistant starts, a washing program is set, and as soon as you start, the machine knocks it out, you must immediately contact an electrician. Problem. most likely in the electric circuit, and it is impossible to make repairs on your own.

Important! It is strictly forbidden to operate the washing machine in such conditions.

to contents ↑

The machine does not heat water

Such a malfunction can often be found in washing machines "Electrolux". The breakdown of the heating element - TENA causes this effect. It is very difficult to confuse this failure with another.

Decision

There is only one solution - replacing the heater. Repairing Electrolux washing machines with your own hands is not an easy task, and replacing a heating element is one of the most difficult options. The main thing is to do everything carefully and in accordance with the manufacturer's instructions.

Important! Before changing the heater, measure it with a multimeter. The problem may not be with him at all, but with the control board.

to contents ↑

Basic codes for Electrolux washing machines

Let's talk about the main error codes. Among them:

1. The familiar E11 is a problem with water intake from a pipeline.
2. E12 - malfunction during drying with water supply.
3. E13 - there is liquid in the pan, which means a crack in the body.
4. E21 - the washer does not drain the water.
5. E23, 24 - a failure during the operation of the pump.
6. E22 - there is no drain on the dryer, a clogging of the condenser system is possible.
7. E31, 32 - malfunctions in the operation of the water level sensor.
8. E33 - power surges.
9. E35 - occurs when the level switch breaks.
10. E36 - malfunctions of the water level relay.
11. E41..45 - problems with the door.
12. E51..54 - there is no connection between the control system and the engine.
13. E55 - engine failure, power failure.
14. E57 - a high level of current in the system.
15. E61, 62 - overheating.

to contents ↑

Stock footage

We discussed such a topic as the “Electrolux” washing machine, its malfunctions, do-it-yourself repair and quick error orientation - all this is now available to you. Use our tips, manufacturer's instructions, and in most cases you can easily solve the problem yourself, without involving the wizard.