How to get rid of mold on the walls?

Before you get rid of mold on the walls, you need to understand what it arises from? Mold - these are dangerous mushrooms that not only spoil the general appearance of the room, provoke unpleasant odors, but are also very dangerous to health. It can cause the following diseases: bronchitis, laryngitis, tracheitis, allergies, thrush, conjunctivitis, dermatitis, stomatitis, bronchial asthma, eczema, and also contributes to the appearance of problems with the musculoskeletal system and joints.

to contents ↑

Causes of mold:

• High humidity in the room.
• Lack of ventilation or poor ventilation.
• Design errors made during the construction of the house.
• Super-tight plastic windows are installed.
• Illiterate repairs made.
• The room is not heated enough.
• The house has thin walls that freeze in cold weather.
• Poor foundation waterproofing.

to contents ↑

How to get rid of the fungus on the walls?

In the event that you find mold in the apartment, you must immediately proceed to its removal. To do this, follow these steps.

Stage 1

Initially, you need to prepare an area for processing so that the fungus removal procedure is effective. For this:

1. Tear off the wallpaper from the affected areas.
2. Take a spatula or a stiff brush.
3. Clean with their help the plaster, which began to exfoliate.

Stage 2

At this stage, we process the walls using a special mold control:

1. Buy a solution to kill the fungus.
2. Moisten a roller or brush in it.
3. Treat the infected surface and the area around it.

Important! For this stage, you can use modern specialized solutions such as: Fongifluid (ALPA), HOMEENPOISTO (TIKKURILA), Senezh Effo or do-it-yourself solutions prepared with folk remedies, the list of which is listed below.

Stage 3

At this stage, prime the affected area with an antiseptic. For this:

1. Pour a deep penetration primer into the construction basin.
2. Prime with a roller soaked in the solution all the necessary places.
3. Allow time to dry.

Important! The applied antiseptic increases the strength of putty, plaster, glue, paint, enhances their durability and prevents the reproduction of fungi or other harmful microorganisms.

Stage 4

Then plaster and plaster the walls.

Stage 5

After the plaster has completely dried, prime the surface with a deep penetration primer again. Allow the treated surface to dry completely, then proceed to the next step.

Stage 6

Bring your room in the appropriate form: paste the wallpaper or paint the surface with paint.

to contents ↑

How to prepare a solution for mold yourself?

There are several folk recipes in order to remove the formed fungus in the house. You can cook them yourself from improvised means.

Recipe 1

To apply this method, you will need one of these tools:

• sodium fluoride 1-1.5 kg;
• copper or iron sulfate - 1 kg.

Next, prepare the solution as follows:

1. Pour 10 liters of water.
2. Dissolve the selected product in it.
3. Thoroughly mix the resulting solution and heat it to 50-60 degrees.
4. Work them the walls.

Important! You can also prepare a remedy for mold, thus: dissolve in 10 liters of water, 0.5 kg of iron sulfate and 0.5 kg of copper sulfate.

Method 2

To get rid of mold on the walls, prepare the following solution:

1. Take 2 liters of acetic acid and 0.5 kg of copper sulfate.
2. Dissolve these ingredients in 10l of pure water.
3. Mix well.
4. Preheat the mixture to a temperature of 50-60 degrees.
5. Apply mortar to the walls with a construction brush.

Method 3

Prepare a folk remedy for mold on the walls in this way:

1. Pour 10 liters of water into a bucket.
2. Dissolve in it boric acid - 0.4 kg, table vinegar - 1.4 liters and borax - 0.9 kg.
3. Thoroughly mix the resulting solution and bring to a temperature of 50-60 degrees.
4. Spray onto walls from a spray bottle or apply with a brush.

to contents ↑

What can be used instead of a primer?

Of course, an antiseptic primer is most effective in order to perform a phased procedure for removing mold, but if there is a need to replace it with something, use the following improvised means.

Bleach

Bleach is a tool that helps to solve the issue of how to deal with mold on hard surfaces, such as: tiles, glass, floor. It contains sodium chloride, which removes not only mold but also its spores. It has the property to discolour the surface. Before applying bleach to the surface, dilute it with water in a ratio of 1:10.

Important! Using this anti-mildew, wear protective gloves and a mask, as it releases toxic and harsh fumes that can harm the body. Use bleach only where the room can be ventilated..

Vinegar

Vinegar is a weak acid that can eliminate the fungus on the walls. It must be sprayed to the surface, and after an hour rinse with clean water. Then ventilate the room.

Important! For preventive purposes, spray vinegar on problem areas once a week.

Hydrogen peroxide

Hydrogen peroxide is an antimicrobial and antifungal agent with which you can get rid of mold in any problem areas of the apartment. It is safe to use, since it does not emit any toxic fumes and does not have a pungent odor.

Important! Hydrogen peroxide - able to whiten the surface, so do not use it on painted materials.

Ammonia

Ammonia - kills the fungus on hard surfaces, not suitable for use on porous. Apply it as follows to get rid of mold on the walls quickly:

1. Dissolve ammonia in water in a ratio of 1: 1.
2. Treat the resulting area with the problem area.
3. Wait a few hours.
4. Rinse off the solution with clean water.

Important! Ammonia in large doses can cause a headache and lead to a sore throat. In no case do not mix bleach and ammonia, since when combined, very toxic gas is released.

Baking soda

Baking soda - a popular substance in the household, is also capable of destroying fungi. Use this anti-mildew agent as follows:

1. Take 1 tsp. food water.
2. Dissolve it in 1 cup of water.
3. Spray the problem areas with the resulting solution.
4. Do not rinse it off.

to contents ↑

Preventive measures against mold:

1. After using the bathroom, leave the door ajar for a while to even out the temperature in it and eliminate humidity.
2. Ventilate all rooms more often and try to install oar plastic windows.
3. When the first black dots appear on the surface, immediately treat them with vinegar or hydrogen peroxide.

to contents ↑

Stock footage

Now you know how to get rid of mold on the walls and, using the advice of our experts, you will certainly cope with this task.So that you do not have the chance to carry out such a long and laborious procedure again after a while, do not forget to monitor the humidity and temperature conditions in your home.