How to clean a bath of limescale

Every day we use plumbing at home, and the current tap water often leaves much to be desired, especially in large cities. Therefore, in order to receive only positive emotions during daily water procedures, everyone needs to know how to clean the bath of limescale without damaging the surface of the bowl and spending a minimum of personal effort.

to contents ↑

When to clean the bath?

As in any other room, it is better to prevent the appearance of plaque than then try to remove it. Therefore, be sure to adhere to the following simple operating conditions for the bathroom in order to ease your household chores:

1. After each water treatment, rinse the bath bowl thoroughly and wipe it dry.
2. Wipe the drops of water on the taps and all the metal, chrome plumbing parts dry so that dry smudges do not form on them.
3. Monthly carry out a full disinfection of the bathroom - this will prevent the growth of fungi and other pathogenic bacteria, and accordingly maintain your health.

to contents ↑

How to remove limescale in the bathroom?

In the manufacture of plumbing items use different materials - plastic, cast iron, steel, acrylic. A specific cleaning agent is suitable for each material.

Take note of the complete list of all necessary detergents and equipment that you will need in order to keep the bathroom completely clean:

• vinegar;
• citric acid - a powder or solution;
• oxalic acid;
• soda - calcined or food;
• special bath cleaners - pastes, creams, powders, washing concentrates;
• bleach based on chlorine;
• aggressive solvents - acetone, white spirit;
• soft and hard sponges;
• metal brushes;
• sandpaper of different grains;
• soft clean rags, preferably light shades.

to contents ↑

How to clean the bath of limescale?

The bowl is most susceptible to unattractive calcareous deposits. Its shape contributes to the drainage of water and its accumulation at the bottom. To quickly deal with the problem, use one of the following methods.

Method 1

The easiest lime removal method:

1. Fill a full bowl overnight with hot water.
2. Dissolve the remedy available to you - vinegar, citric acid, soda ash or oxygen bleach.
3. Drain the water in the morning.
4. Wipe the inside of the bathtub with a sponge. If heavily soiled, use soda or a special cleaning powder.
5. Rinse all chemical residues and lime off the shower well.
6. Wipe dry.

Important! This option is suitable for cleaning any material. Therefore, if you are wondering, how to remove limescale from plastic in the bathroom, perhaps, no better means can be found.

Method 2

Good pastes, powders and creams quickly help completely remove lime deposits. The principle of their use is extremely simple:

1. Apply the cream on the soft (for acrylic) or harder side (for cast iron and enamel surface) of the sponge.
2. Wipe dirt in circular motions.
3. Leave the product without rinsing for 30-40 minutes after the entire surface has been treated.
4. Rinse off the cleaner while wiping the inside with a bath sponge.
5. Rinse with a shower to wash off all remains of cream and lime.
6. Wipe the bath.

Important! When buying such a tool, do not chase cheapness. Acquire products from trusted brands that really give a quality result so that the time spent on cleaning does not go to waste.

Method 3

Always suitable for cleaning any surface is ordinary soda. It is also easy to remove calcareous deposits and even bleach the surface. To use it correctly, do the following:

1. Rinse the bath.
2. Apply powder to a sponge.
3. In successive rubbing movements, go over the entire surface, regularly adding powder as needed.
4. Leave the soda in the bathtub for 1-3 hours.
5. Rinse and dry the bath well.

Method 4

The most aggressive way will require the use of several cleaning products at the same time. The procedure for removing lime from the bath is as follows:

1. Rinse the bowl.
2. Walk well over the entire surface with a metal brush or sandpaper with a small grain size (120-150).
3. Prepare a solution of citric, acetic or oxalic acid.
4. Apply it on the coating and leave for 30-40 minutes.
5. Sponge the surface while rinsing with warm and then cool shower water.
6. Wipe with a soft cloth until all moisture is removed.

Important! If the bathtub is acrylic, apply a special repair paste to hide scratches and other mechanical damage. Treat with polish.

Method 5

Special cleaning and disinfecting sprays are very easy to use. Use them as follows:

1. Spray the liquid on the entire surface so that it does not remain smudges, but is evenly distributed throughout the bathroom.
2. Leave on for 30-60 minutes for the chemistry to work.
3. Wear protective gloves and a respirator.
4. Take a sponge and treat it all over the bathtub in a circular motion.
5. Rinse thoroughly with running water.

Important! When choosing the right product, keep in mind that such brands as Domestos, San Klin, CIF, Mr. Muskul, Amway, Ravak have proven themselves well.

to contents ↑

How to clean the tap of limescale?

Faucets and shower heads have, as a rule, a relief surface with bends. For this reason, it is not very convenient to clean them, and if you don’t know the effective methods, the procedure can take a lot of time, and the result will be far from expected.

Get familiar with the effective methods for removing lime from the tap and shower head, detailed instructions for which are outlined below.

Option 1

1. Mix water and vinegar (7%) in equal proportions.
2. Wet the sponge in the solution and sequentially process the entire surface of the tap.
3. Rinse with running water and wipe dry with a clean cloth.

Option 2

1. Preheat the vinegar.
2. Soak a cloth in it.
3. Wrap a faucet or shower head.
4. Leave on for 30-60 minutes.
5. Rinse with running warm water.
6. Wipe the surface well.

Option 3

1. Unscrew the gander or shower head.
2. Pour water into any container of a suitable size and pour citric acid powder at the rate of 0.5 l 4 tbsp. l cleaning.
3. Put the plumbing part in the solution and leave it for 1-2 hours - it depends on the degree of pollution.
4. Remove from solution and rinse with running water.
5. Wipe dry.
6. Screw the part into place.

to contents ↑

Useful Tips

to contents ↑

Stock footage

1. Do not ignore recommendations regarding necessary remedies. Gloves will protect your skin from allergies, and the mucous membranes of the eyes and respiratory tract from chemical burns.
2. Before using any chemical agent, be sure to carefully read the instructions from the manufacturer to use it correctly and not harm yourself or your plumbing.